1.0

Major VersionM

by Joshua

Introduction

This project uses a Crazy Circuits Touch Board to change the pattern of 5 LEDs on the shirt. While the project isn't technically difficult, the amount of sewing involved makes this a difficult project. If you've never sewn before, we'd recommend you practice on other projects first.

Video Overview

  1. Overall, wiring is simple. Five LEDs hooked up to specific pins, and utilizing a common Ground.
    • Overall, wiring is simple. Five LEDs hooked up to specific pins, and utilizing a common Ground.

    • Pin 15 is connected to a Conductive Thread lattice that is sewn into the NASA Letters. This serves as the interactive Touch Point.

    • We're using a 3 AA holder hooked up to the Screw Terminal Chip to power the shirt when it's being worn.

    • If you're unhappy with what pins we're using as outputs, you can always change that in the code later on. Just make sure you're using PWM pins.

    Add Comment

  2. Lay your parts out on your shirt.  Make sure your LEDs are where you want them.
    • Lay your parts out on your shirt. Make sure your LEDs are where you want them.

    • The Space Shuttle patch and LED is optional. The code we're using utilizes that LED, but leaving it out is just fine.

    Add Comment

    • The NASA letters are going to be our Touch Point, but we need to fill them in first.

    • Sew a grid or lattice over one or all letters.

    • If you can, use a single strand of Conductive Thread for all the letter. Otherwise connect them with Conductive Thread. We need to make them a single connected Touch Point.

    Add Comment

    • Use standard thread to sew the LEDs down.

    • Treat them like a button.

    • We're using some standard black thread. You can use any color as long as it isn't conductive.

    Add Comment

    • Lay out the Touch Board and Screw terminal.

    • Sew down the Touch Board with regular thread.

    • Try and not use the same holes you're going to use with the Conductive Thread.

    Add Comment

    • Start with the Ground pin on the Touch Board and sew your common ground.

    • We sewed one solid line of Conductive Thread around the NASA logo, with it ending on the furthest out LED.

    • We then connected each LED to the common ground with a another line of thread.

    • Remember, in Crazy Circuits the holes with white around them are Negative (Ground).

    Add Comment

    • Reference the diagram to see which pins we're using for which LEDs.

    • It doesn't matter HOW you get to the Positive side of each LED, as long as you don't cross any "wires". AKA The Conductive Thread.

    • With Conductive Thread, remember that you have two layers of shirt to work with, which is useful for jumping under or over other lines of thread.

    Add Comment

    • Sew the Screw Terminal Chip down with regular thread.

    • Connect the Positive to the 5V (VIN) pin on the Touch Board, and the Negative side to the Ground pin on the Touch Board.

    • Feel free to attach your AA or AAA Battery Holder to see if your connection is strong. While we've not uploaded code yet, an LED on the Touch Board should turn on.

    Add Comment

    • You may wish to save this step until after you've coded and tested everything.

    • Using a sewing machine and regular thread to secure down your Conductive Thread lines.

    • We used a zig zag pattern.

    Add Comment

    • If you're using a Shuttle patch, sew it on now using regular thread.

    Add Comment

    • Cut a piece of fabric out and pin it to your shirt.

    • Sew it down using regular thread.

    • Just make sure it fits your battery holder.

    Add Comment

    • If you've never used a Touch Board before, try practicing uploading code and reviewing the Touch Board User Guide.

    • Plug in your Touch Board and open up the Arduino Software.

    • Open up a new project window. Copy and Paste this code into the project window.

    • Upload the code and see if it works.

    • The "Shuttle" LED will turn on and fade automatically. When a user touches the Touch Point all the LEDs will start to fade.

    • When the program turns on, it needs 3-5 seconds to Calibrate the Touch Point. During that time an LED on the Touch Board will turn on. When Calibration is finished that LED turns off.

    Add Comment

    • When doing any testing, make sure your shirt is spread out. A dummy body or cardboard insert will help out greatly.

    • Don't feel that you need to do amazing stitch work with the Conductive Thread. Do large stitches and then secure them down later.

    • When in doubt, post questions to the forums.

    Add Comment

Finish Line

Joshua

Member since: 11/16/2017

47 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 2

Past 7 Days: 10

Past 30 Days: 32

All Time: 327